Slab Leak Location Wellington FL means pinpointing the exact spot where a pipe under your concrete floor is losing water, without tearing up half the house. We handle homes and businesses across Palm Beach County, from Binks Forest to Olympia. If your water bill jumped and the floor stays warm, call (561) 760-4218 and we will trace it the same day.
Isolate the zonesScan the slabMark the breakEvery trace covers the full diagnostic sequence, not just a listen-and-point. Here is what is included in the base fee, and what we quote separately if the job calls for it.
We shut the main and separate domestic supply from irrigation, pool and any other loop tied to the system. Each zone gets pressure tested with a RIDGID pump so we know exactly which line is losing water before we scan anything.
A full walk of the affected slab with an ultrasonic leak detector and Sewerin listening device, cross-checked with a FLIR thermal camera. We scan until two technologies agree on the same location, then confirm with a second pass.
The leak spot gets marked on the slab with paint and photographed with a tape measure for reference. You get the distance from two fixed points so your plumber can lay out the access cut without any exploratory demolition.
A summary covering leak location, pipe material, estimated loss rate and the methods used. This is the document your insurance company or utility may ask for if you pursue a bill adjustment or a claim.
If you want us to handle the pipe leak repair, we quote it on the spot based on access depth, pipe material and slab type. If you prefer your own plumber, the report gives them everything needed to do the job right.
When we do the repair, we pressure test the line again before closing the slab. You see the gauge hold steady before concrete goes back. That final check is how you know the fix is done, not just covered up.
The approach is the same for a home and a business. What changes is the access, the schedule and who needs the paperwork.
Slab leaks show up as a climbing water bill, a warm floor spot or the sound of running water with everything off. We trace the break and mark it so your repair stays small.
Commercial slab leaks disrupt tenants and run up utility costs fast. We isolate the supply, trace the break and coordinate access around your operating hours.
A plain-language look at what Slab Leak Location involves and when it is needed.
See how it worksSlab Leak Location Wellington FL is a diagnostic service that pinpoints where a pressurized water line under your concrete slab is leaking, using sound, heat and pressure instead of demolition. We pressurize the line, walk the slab with acoustic listening devices and a Fluke thermal imaging camera, then mark the break within a few inches. Most homes here are built on post-tension or monolithic slabs with copper or PEX tubing buried underneath, so guessing is expensive. We confirm the leak, mark it, and hand you a repair plan the same visit.
Wellington homes sit on sandy soil and high water tables, and that combination works on buried pipe. Copper lines pit from the outside, PEX fittings fatigue, and irrigation lines cross under driveways more often than owners realize. A slab leak detection Wellington call usually starts the same way: a water bill that doubled, a warm patch by the hallway, or the sound of running water with every fixture shut off.
Finding the break before the concrete opens is what keeps a slab leak repair small.
Five steps, no guesswork. Here is exactly what happens from the moment you call until we hand you the marked location and report.
We ask about your water bill, the meter reading with everything off, warm floor spots and any sound of running water. That five-minute conversation tells us whether this is a slab leak, an irrigation line leak or a pool leak, so we bring the right gear. You get a two-hour arrival window, not a full day.
On arrival we shut the main, isolate the domestic lines from irrigation and pool loops, then pressure test each zone with a RIDGID test pump. This takes 20 to 30 minutes and confirms which system is losing pressure. Skipping this step is how other companies end up breaking concrete over the wrong pipe.
We walk the slab with an ultrasonic leak detector and Sewerin acoustic listening device, then cross-check with a FLIR thermal imaging camera. Pressurized water escaping a pinhole hisses and creates a temperature signature. Two technologies agreeing on one spot is how we get within a few inches.
We confirm the reading with a second pass, sometimes using tracer gas on low-pressure lines where sound alone is inconclusive. Then we mark the slab with paint, photograph the location with a tape measure for reference, and note the depth and pipe material. You see exactly where the repair access goes.
Before we leave you get a written summary: leak location, pipe material, estimated loss rate and photos. If you want us to handle the pipe leak repair, we quote it on the spot. If you use your own plumber, the report gives them everything they need to cut once and fix it right.
Move across a circle, or focus it and press Enter, for an illustrative thermal view of the photograph.
Amplify the hiss of pressurized water escaping a pinhole under concrete. We walk the slab in a grid pattern and compare readings to narrow the source to a few inches.
Reveal temperature differences on the slab surface caused by hot or cold water escaping below. Hot-water leaks show up as a warm signature that is easy to map and confirm.
Pressurize each zone in isolation to confirm which line is losing water. This step eliminates irrigation, pool and service line leaks before we scan the slab.
Provide a second acoustic opinion on deep or low-pressure lines where a single reading is not conclusive. We cross-check every mark with at least two instruments.
Used on low-pressure or buried lines where sound alone is unreliable. A safe gas mixture is introduced into the line and detected at the surface above the break.
Thermal views are illustrative, generated from the photographs.
Inspect sewer and drain lines under the slab for cracks, root intrusion and separated joints that can mimic a supply leak with moisture and odor.
Map the wet area and trace the path of buried metal pipe before scanning. Knowing the pipe route keeps the acoustic search focused and shortens the job.
We shut the main and separate the domestic supply from irrigation, pool and any other loop. Each zone is pressurized and monitored for drop. This step takes 20 to 30 minutes and prevents the most common mistake in slab leak work: scanning the wrong system.
No location is called off a single reading. We require acoustic and thermal results to agree on the same spot, then confirm with a second pass. On low-pressure or deep lines we add tracer gas. Two or three technologies agreeing is how we get within a few inches.
We walk the slab in a consistent grid, logging readings at each point and triangulating the strongest signal. This is slower than a quick listen but far more accurate. It is the difference between a marked spot that holds up and one that sends the plumber on a second hunt.
When we handle the repair, we pressure test the line again before closing the slab. You watch the gauge hold steady. That final check confirms the fix is sound and the system is back to normal operating pressure.
We isolate the domestic supply, pressure test it and confirm the loss is under the slab. Acoustic and thermal scans pinpoint the break near the kitchen wall. We mark it and document the loss rate for a utility adjustment request.
Outcome: The plumber cuts one small access panel, repairs the copper line and the next bill returns to normal. Total concrete removed: about 4 square feet.
A tenant in a Royal Palm Beach rental reports a warm patch on the bathroom tile that never cools down.
Thermal imaging confirms a hot-water line leak under the slab. We cross-check with acoustics, mark the spot and provide the property manager with a written report and photos for the owner.
Outcome: The repair is scheduled with full documentation, the tenant stays in place, and the owner avoids replacing the entire bathroom floor.
A family in Saddle Trail Park hears running water at 2 a.m. with every fixture shut off and the meter still spinning.
We take the emergency call, arrive within the two-hour window and isolate the system. The leak is in the domestic line under the hallway. Acoustic scanning marks it within a few inches of the wall.
Outcome: The line is repaired the next morning, the meter stops spinning, and the family avoids a weekend of water damage and a much larger bill.
An equestrian property in Palm Beach Point has saturated ground near the barn and a climbing water bill.
We separate the irrigation loop from the domestic supply and pressure test both. The loss is in an irrigation lateral, not the slab. We trace it with acoustic equipment and mark the break for the landscape crew.
Outcome: The irrigation line is repaired without touching the barn slab, saving the owner thousands in unnecessary concrete work.
A commercial tenant in a Wellington plaza reports moisture along an interior wall and suspects a slab leak.
We isolate the commercial supply, pressure test it and scan the slab with acoustic and thermal tools. The leak is confirmed under the slab near the utility room. We mark it and coordinate access around business hours.
Outcome: The repair happens overnight, the tenant opens on time the next morning, and the moisture issue is resolved at the source.
Wellington sits on sandy fill over a high water table, and that combination is hard on buried pipe. Copper lines corrode from the outside in, PEX fittings fatigue at crimp points, and irrigation laterals cross under driveways more often than owners expect. We adjust our acoustic gain settings for this soil because sound travels differently through sand than through clay.
Homes in Palm Beach Polo and Equestrian Club often have larger footprints and multiple wet zones, so isolation takes longer but saves far more concrete. Newer builds in Grand Isles and Isles at Wellington tend to use PEX, where leaks cluster at fittings rather than mid-run. We also see a seasonal pattern: after a dry spring, the soil shifts and old copper joints start weeping.
If you need affordable slab leak detection in Wellington FL, the fastest path is a same-day trace before the damage spreads into flooring and cabinets.
Before: No visible leak, no wet spots, just a meter that kept spinning. Two other companies had listened and guessed without confirming.
After: We isolated the domestic supply, confirmed the loss under the hallway slab, and marked the break within 3 inches of the wall.
We recommended a pressure regulator check because the home was running at 95 psi, which stresses copper joints. Keeping pressure between 50 and 70 psi extends the life of the whole system.
Before: A homeowner in Olympia noticed a warm patch on the bathroom tile that never cooled. The hot-water line under the slab was leaking and heating the concrete. The concern was replacing the entire bathroom floor.
After: Thermal imaging mapped the warm signature, acoustics confirmed the break, and we marked it near the vanity. The repair required a single 18-inch cut. The floor was patched with matching tile, and the warm spot disappeared.
We suggested flushing the water heater annually and checking the anode rod, since hot-water lines under slabs take more stress when the heater runs at higher temperatures.
Before: A family in Saddle Trail Park heard running water at 2 a.m. with every fixture shut off. The meter was spinning fast. They called us and we arrived within the two-hour window to find the source before morning.
After: We isolated the system and traced the leak to the domestic line under the hallway. Acoustic scanning marked it within a few inches. The line was repaired the next morning, the meter stopped spinning, and no flooring was lost.
We recommended a whole-house shutoff valve install so the family could isolate the supply instantly if it ever happens again. That one valve can save thousands in water damage.
Most slab leak calls start with one of these symptoms. If you recognize yours, get it traced before the damage spreads under your flooring.
A marked break means one small cut instead of a torn-up floor.
When we mark the leak within a few inches, your plumber cuts one small access point instead of a trench across the living room. On a typical 1,800-square-foot Wellington home that saves 20 to 40 square feet of slab removal, plus the tile, thinset and finish work that goes with it. You pay for a repair, not a remodel.
Most slab leak detection services in Wellington, Florida we run are finished in two to four hours. You get a marked location, a written summary and photos before we pack up. No waiting three days for a second opinion while water keeps running under your floor and your bill keeps climbing.
Once we locate it and your plumber repairs it, the next billing cycle usually returns to normal. We document the loss rate so you have proof for a utility adjustment request.
Water under a slab wicks up through the concrete and ruins laminate, engineered hardwood and base cabinets from below. Finding the source early keeps the damage to one small area. We also check moisture meters along the baseboards so you know whether drying equipment is needed before mold gets a foothold.
What a written scope covers and what shapes it. Prices are set by the business after the first look.
Included
Depends on
Clear records you can keep and share.
Paint mark at the confirmed break location
Images with tape measure for reference
Leak location, pipe material, loss rate
Optional pricing if we handle the fix
Both cause moisture, but they behave differently and need different tools to trace.
Pressurized water line losing water continuously
Waste line leaking only when water runs
Sprinkler lateral losing water outside the footprint
A list like this tells people straight away whether you cover their street. Not listed? Call and ask: it only takes a minute.
Based in Wellington and covering the places around it. Pick one for local details.
A slab leak is a break in a water line running beneath your concrete foundation. We locate it by isolating the system, pressurizing the line, then scanning the slab with acoustic listening devices and a thermal imaging camera. When both tools point to the same spot, we mark it within a few inches and document the reading. Most traces take two to four hours.
Post-tension slabs and homes over 3,000 square feet sit at the higher end. The fee covers isolation, acoustic and thermal scanning, marking and a written report. Repair is quoted separately if you want us to handle it.
Yes. That is the entire point of the service. Acoustic listening devices pick up the hiss of pressurized water escaping a pinhole, and thermal cameras reveal the temperature signature on the slab surface. We confirm with a second pass before marking. Concrete only gets opened after we have pinpointed the break, and then only a small access area.
They are common here. Sandy soil, a high water table and irrigation-heavy lots accelerate corrosion on copper pipe and stress PEX fittings. Homes built in the 1980s and 1990s with copper under the slab are the most frequent callers. If your water bill jumped and you hear running water with everything off, get it traced before the damage spreads.
Other services from the same team.
Water under your slab does not stop on its own, and every day it runs costs you money. Call (561) 760-4218 and we will schedule a same-day trace with acoustic and thermal equipment. You get a marked location and a written report before we leave.
Call us at (561) 760-4218 or email info@wellingtonleakdetection.com. Most inspections are scheduled same-day or next-day. We serve Wellington and all of Palm Beach County.
